Print Head Cleaning

In this modern world, the printer has become one of the essential parts of our life. Without this, we can’t even think to live. As everyone now using modern technology instead of writing in a notebook.

Servicing the printer is also important to give 100% performance. Clogged in a printhead is one of the problems that is usually found in some printers. The one who used to print daily didn’t find that issue commonly but the one who used their printer one time in a week.

Another printer that is also known as a 3D printer, is used to create 3D objects. Sometimes, filament blobs get stuck and get hardened. So don’t worry about that or don’t get frustrated.

This can be done just because of using low-quality filament blobs. If you use pteg filament blobs then of course it wouldn’t happen.

If you are interested then go and have a pteg filament review. This is an outstanding blob.

This is not a big issue that you have repaired it or bought a new one. In fact, this can be easily removed.

What Is a Print Head Cleaning?

Print Head Cleaning

A print head cleaning is the same as you what you heard. It is an easy and simple process of taking off the ink from the cartridge or upgrading the rate of flow of ink during printing.

Let’s compare this with car maintenance. You are driving your car without changing the car’s oil. You absolutely drive your car more than 5,000miles without an oil change, but it’s not for you and also not for your car engine.

The same can be said about your printer as daily service is required to keep it functioning properly. There are a few ways through which you can fix your printer, easily without investing your money, depending on the acerbity.

Automatic Printhead Cleaning:

This is the easiest step or you can say the easiest way of cleaning clogs. If your printhead is only got clogged then you will be able to solve it in a second.

Whenever you turn your printer on, a maintained cycle is initialized.

This method clears dry ink, debris from your cartridge nozzle and allows the ink to flow from your cartridge into the internal, and out of the print head in order to lose any clogged or obstructed nozzle.

Method #01; Damp Paper Towel Application:

This method is usually found one of the simplest and easiest among all. Mostly print head found directly on the cartridge, simply uninstall the cartridge. Take a damp paper apply it to the print head nozzle and wipe it down.

You will clearly see the ink will descend and change into a liquid as exposed to water. The clogged ink will begin to wipe off. As the cartridge gets dry, install it into the printer again.

Method #02; Soaking:

This method can only be used when the above is not working. This is a little bit intense but 100% efficient. Take 1:1 of water and isopropyl alcohol and mix it well. Then keep ONLY printer head into this solution.

This method will break down chunks into color liquid. Keep the print head into the solution for 24 hrs then remove and dry it completely and reinstall back.

Method # 03; Use Pliers to Remove the Blob:

Take a couple of pliers and softly remove the blob of plastic from the extruder. If the contact point is melted then you don’t have to apply force on it. If you did it by your hand then it will be dangerous and might get burned.

Method # 04; Use a Brass Brush to Get the Last Bits:

When you completely remove the blocks of plastic then apply the Brass brush and clean it. This will help you to clean the remaining small chunks of plastic.

Give some extra focus to the nozzle area or replace it. It is cheap and easily available everywhere. If you didn’t do this then you will face problems in the future.

Conclusion:

At the end of the day, a block of ink will be no more found. Even if you don’t use your printer every day, you can just turn it on once a week to commence its maintenance cleaning process so that your printer ink cartridge can perform to its fullest potential.

This will confirm that your printer head will never get blocked at first. But if this will cause too much trouble for you then just chill it out and use the above method for solving your problem.

Leave a Reply

Your email address will not be published. Required fields are marked *